Independent tube biasing?

ask your general tube related questions here

Independent tube biasing?

Postby fcervone » Wed May 04, 2016 4:52 pm

i hope this is not a stupid question but here goes. Why dont more amp manufacturers use independent tube biasing? I had a maven peal amp that you could set the bias on each tube independently. No need for matched tubes.

Thanks
fcervone
 
Posts: 1
Joined: Sun Feb 21, 2016 11:10 am

Re: Independent tube biasing?

Postby battradio » Wed May 04, 2016 7:31 pm

Cost and most users would never bother to set it correctly .
Mark
Image
User avatar
battradio
KT88
 
Posts: 927
Joined: Tue Mar 10, 2009 12:58 am
Location: near ST.Louis MO.

Re: Independent tube biasing?

Postby Geek » Thu May 05, 2016 1:04 am

Depends on who the amp is target marketed toward. If the masses, the above is painfully true.

For higher end builds, they exist with detailed instructions (Rogue Audio) or many others have free biasing (you supply the tubes) from their authorized depots.

Cheers!
-= Gregg =-
Fine wine comes in glass bottles, not plastic sacks. Therefore the finer electrons are also found in glass bottles.
User avatar
Geek
KT88
 
Posts: 3585
Joined: Sun Oct 21, 2007 3:01 am
Location: Chilliwack, British Columbia

Re: Independent tube biasing?

Postby burnedfingers » Fri May 06, 2016 5:44 am

If you remember years ago cars had wing vents in the driver and passenger doors. A bean counter figured that Ford motor company could save aproximately .78 per unit by getting rid of those vents. The result was two fold. Not only did they save money on each unit out the door but the people buying these cars now were purchasing AC instead of going without it. BAck to independant biasing.. who will loose? The tube suppliers won't be selling you matched pairs at inflated prices. The amplifier manufacturer will loose profit because of adding additional pots and resistors. The bottom line is usually a money factor. There are some of us that will take the time to modify our circuits to have individual tube bias because we see the merit behind the idea.
burnedfingers
KT88
 
Posts: 640
Joined: Mon Sep 05, 2005 6:38 am

Re: Independent tube biasing?

Postby paart » Sat May 07, 2016 9:37 am

Being able to independently set a DC bias point for two output tubes doesn’t eliminate the need for matched tubes. While doing so is beneficial in reducing the DC component in the output transformer primary at idle, it doesn’t ensure that the two tubes will conduct identically at 25, 50 or 100 percent power output.
This can be thought of as the AC balance of the output pair. While some designs incorporate an AC balance control for the phase splitter, it ends at that point. If the output tubes do not have matching curves so that the “AC” balance is maintained in that stage, then increased distortion will result.

Due to production tolerances, all tubes deviate from the published plate or transfer characteristic curves in a number of ways. The published curve is an ideal, or average, and individual tubes will deviate from this. Setting the grid bias at idle sets the relationship between grid voltage and plate (and screen grid, if applicable) current at one point only. During operation this relationship will vary from tube to tube, as the grid voltage is varied over a wide range.

The same thought applies to trying to match tubes on a tube tester. A tube tester only measures the transconductance of the tube at one point on the curve. Two tubes that show the same reading on a tester at the specified grid voltage (sometime labeled “bias”) may show considerably different results at a different grid voltage.

Be careful where you buy your “matched tubes”. True tube matching requires special equipment and knowledgeable people!
paart
 
Posts: 95
Joined: Mon Jul 17, 2006 8:36 pm
Location: Central PA

Re: Independent tube biasing?

Postby dcriner » Sat May 28, 2016 4:46 pm

When a seller claims that tubes are matched, it is likely that just their emission is close - or maybe nothing at all. Even if perfectly balanced, tubes' performance change with age.

For my ST-70, I aspire to reset the bias every so often, but often just wait until next year.
Doug Criner
dcriner
KT88
 
Posts: 309
Joined: Mon Oct 23, 2006 4:19 pm
Location: Illinois


Return to tube 101

Who is online

Users browsing this forum: No registered users and 3 guests