Currawong

the thermionic watercooler

Re: Currawong

Postby soundbrigade » Thu Sep 07, 2017 1:11 am

Tom, I haven't made a final descision of OP transformers. I think I can use a pair of Edcore XPP from a retired 6AQ5-amp, else I am considering any of these:
http://en.uraltone.com/electronic-components/transformers-and-chokes/output-transformers/all-output-transformers-as-list/inmadout-output-transformer-tu84m18c.html
Or a Hammond 125E.
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby EWBrown » Mon Sep 11, 2017 7:00 pm

I have a pair of Hammond 1609s as well as three 1608s, that I purchased (or traded for) about 10 years ago.
TBD on the power trannie, I have several options to choose from.

The board and parts was a nickel short of $36, and I have all the tubes on hand, both in 6.3 and 12.6V filament voltages.
12V would make it simple, I'd just use a 12V 4 A SMPS "brick" and thusly eliminate any 60HZ from the board -
or I could use 6.3V tubes and wire them in series, in pairs.

Or, I I could go back to the method I used in my 13EM7 SE amps, use one of the Trafomatic toroids, and use 12.6V filaments in series pairs.
I think 700mA at 26VDC should be sufficient to meet the requirement.

So, there is no additional monetary expense necessary, just have to ramp up the enthusiasm and start building, after a few years' hiatus.

/ed B in NC
Real Radios Glow in the Dark
User avatar
EWBrown
Insulator & Iron Magnate
 
Posts: 6389
Joined: Wed Mar 19, 2003 6:03 am
Location: Now located in Clay County, NC !

Re: Currawong

Postby soundbrigade » Tue Sep 12, 2017 12:29 am

I feel I need some distance before giving the Currawrong another go (I replaced the blown fuse). Instead I have anothe rproject for 6L6s that a little resembles the 6V6 a little. The single input/splitter/driver tube, 12AT7. Picked this one beacuse of its simplicity. The CCS is a LM317 but got inspired by a build of the OddWatts in another forum to pick the K-version (TO3) as that would fill a hole in my chassis.
The only place in Sweden stocking 317K's wanted almost 10 bucks/each whereas I got five of the (two working hopefully :/ ) from Chian for half that sum.

PP6L6.jpg
PP6L6.jpg (41.04 KiB) Viewed 116 times


The hole and the ordinary LM317.

6L6-31.jpg
6L6-31.jpg (137.68 KiB) Viewed 116 times


OOOPS!!!! I had apperantly planned to use the holes for tube VU-meters ....

6L6-46.jpg
6L6-46.jpg (131.99 KiB) Viewed 116 times
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby EWBrown » Thu Sep 14, 2017 2:58 pm

I like that one, very elegant in its simplicity, no floobydust, blue flashing LEDs or embryonic baby cattle required ;-)

And if one truly desires to have NFB, it is a simple matter of injecting a wee sample of the 8 ohm output back into the top of R5. [:)

I'd use 10M45S in place of the LM317, just because... *) (b) (y)

Approx 8 mA per 12AT7 triode, that is a good plate current for these, makes them really perform!

Even though I have a plethora of 20 year old LM317s on hand, I like the 10M45S as a current source or sink. And have LOTS of them.

Six of one, half a dozen of the other. $)

Or when truly high voltage ratings are required, 10M90S (900 maximum DC volts (666)


/ed B in NC
Real Radios Glow in the Dark
User avatar
EWBrown
Insulator & Iron Magnate
 
Posts: 6389
Joined: Wed Mar 19, 2003 6:03 am
Location: Now located in Clay County, NC !

Re: Currawong

Postby soundbrigade » Thu Sep 14, 2017 3:05 pm

So here we don't go tuberolling. We go regulatorrolling!!!! (banana)
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby soundbrigade » Fri Sep 15, 2017 1:44 am

I just dug up a pair of 10K, 15W transformers when I was vacuuming our flat. Well they stood on a shelf and I have been looking at them every now and then, but considered them to be single ends.

How much will gain/loose using them instead? I get it that I will have less power but lower distortion, but still; are they suitable for the 6V6s?
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby EWBrown » Fri Sep 15, 2017 7:52 am

10K is just about perfect for 6V6s in cathode-biased operation. 8K is better for fixed-bias, but either value is OK.

For 6L6s, 6.6K A-A is a good value.

/ed B
Real Radios Glow in the Dark
User avatar
EWBrown
Insulator & Iron Magnate
 
Posts: 6389
Joined: Wed Mar 19, 2003 6:03 am
Location: Now located in Clay County, NC !

Re: Currawong

Postby soundbrigade » Fri Sep 15, 2017 8:43 am

I did ordered a pair of Hammond 125E's. Maybe use them in the Currywrong. ;)
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby soundbrigade » Wed Sep 20, 2017 1:03 am

I may have a need for a gain stage to both the 6V6 and 6L6 pushpullers. I had an idea of using as´pensize tube hidden in the chassis, something like this:

Hybrid-2sk1058-.gif
Hybrid-2sk1058-.gif (34.2 KiB) Viewed 36 times
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby EWBrown » Wed Sep 20, 2017 9:08 am

One must always utilize the Triode of Improved Reliability! [:) $) :/ O:) (banana)

https://frank.pocnet.net/sheets/113/6/6S31B.pdf
Last edited by EWBrown on Wed Sep 20, 2017 9:34 am, edited 1 time in total.
Real Radios Glow in the Dark
User avatar
EWBrown
Insulator & Iron Magnate
 
Posts: 6389
Joined: Wed Mar 19, 2003 6:03 am
Location: Now located in Clay County, NC !

Re: Currawong

Postby soundbrigade » Wed Sep 20, 2017 9:25 am

No need. I always find it much better to go skydiving without parachute. (y)
Magnus

"It is always more difficult to fight against faith than against knowledge."
User avatar
soundbrigade
KT88
 
Posts: 1732
Joined: Mon Jan 28, 2008 4:57 am
Location: Little Paris, Sweden

Re: Currawong

Postby EWBrown » Wed Sep 20, 2017 9:32 am

No parachute necessary - :[ just use a really long bungee cord ;-) =:o (stop)
It's not the fall that kills, it's the sudden stop at the bottom :))
Real Radios Glow in the Dark
User avatar
EWBrown
Insulator & Iron Magnate
 
Posts: 6389
Joined: Wed Mar 19, 2003 6:03 am
Location: Now located in Clay County, NC !

Previous

Return to diy hifi

Who is online

Users browsing this forum: No registered users and 2 guests