My g*s*g progress - June 30, 2009
Posted: Tue Jun 30, 2009 9:43 pmget*set*go # 6
5 PM
11 PM
5 PM
11 PM
I think that is your second one with that layout, very clean great job.
Brad
diytube.com
new registrations are closed at this time
http://www.diytube.com/phpBB2/
My g*s*g progress - June 30, 2009
Page 1 of 1
Posted: Tue Jun 30, 2009 9:43 pmRe: My g*s*g progress - June 30, 2009
Posted: Tue Jun 30, 2009 11:10 pmPosted: Wed Jul 01, 2009 4:11 amThanks Brad -
I built it for a guy who missed the first one on eBay.
He requested the power switch on the front and the
RCA's on the back - otherwise it's the same.
I built it for a guy who missed the first one on eBay.
He requested the power switch on the front and the
RCA's on the back - otherwise it's the same.
Posted: Wed Jul 01, 2009 4:30 amYou built the ST70 in only 4 hours. What took you so long? 
Nice looking work, as always Tom. Which RCA jacks are you using? I never seem to order the same style, and I'm still trying to decide which ones I like the best.
Nice looking work, as always Tom. Which RCA jacks are you using? I never seem to order the same style, and I'm still trying to decide which ones I like the best.
Posted: Wed Jul 01, 2009 6:37 amThe ST-70 was faster because there were no holes to make !
I've never gotten the same RCA jacks twice ... I usually buy them
on eBay from someone in Hong Kong, I've gotten good
ones and bad ones.
I've never gotten the same RCA jacks twice ... I usually buy them
on eBay from someone in Hong Kong, I've gotten good
ones and bad ones.
Posted: Wed Jul 01, 2009 12:27 pmI have been buying my rca's from here. Like that they come with the right color wahshers unlike the ones on ebay. They cost a little more but think the quality is better.
http://www.markertek.com/Cables-Connect ... 67-2.xhtml
I also use them to purchase this wire for wiring filaments.
http://www.markertek.com/Cables-Connect ... 1000.xhtml
Brad
http://www.markertek.com/Cables-Connect ... 67-2.xhtml
I also use them to purchase this wire for wiring filaments.
http://www.markertek.com/Cables-Connect ... 1000.xhtml
Brad
Posted: Wed Jul 01, 2009 2:17 pmIf there were a category in the Guiness Book of Records for tube amp building (most prolific and shortest production time), your record will be the one everyone would be after. Seriously, it takes me 4 hours just to decided which one to build. Good work.
Min
Min
Posted: Wed Jul 01, 2009 6:04 pmTom,
From where are you buying your Sovtek 6B4G, if you don't mind me asking?
From where are you buying your Sovtek 6B4G, if you don't mind me asking?
Posted: Wed Jul 01, 2009 8:13 pmecir38 wrote:I have been buying my rca's from here. Like that they come with the right color wahshers unlike the ones on ebay. They cost a little more but think the quality is better.
http://www.markertek.com/Cables-Connect ... 67-2.xhtml
I also use them to purchase this wire for wiring filaments.
http://www.markertek.com/Cables-Connect ... 1000.xhtml
Brad
+1 on the Neutrik RCA jacks from Markertek. I use them on all of my DIY stuff.
I still am hunting for good 5-way binding posts. I used Cardas on my GSG but they are too damned expensive to use on everything....
Bill
Posted: Wed Jul 01, 2009 8:42 pmI've been buying the 6B4G's from TubeDepot ....
http://www.tubedepot.com/so-6b4g.html
They are up to $ 99.95 a set - I think they were about 79 when
we started building these amps.
Those Markertek RCA's look good - not a bad price either.
http://www.tubedepot.com/so-6b4g.html
They are up to $ 99.95 a set - I think they were about 79 when
we started building these amps.
Those Markertek RCA's look good - not a bad price either.